• One Storage Cage (either Internal Storage Cage or Front Access Storage Cage) and one system disk

• If Internal Storage Cage is selected:
• Mandatory selection of one IDE or one internal SCSI system disk drive
• Mandatory selection of SCSI adapter and SCSI cable kit required for internal SCSI disks and tape

• If Front Access Storage Cage is selected:
• Mandatory selection of one Universal SCSI system disk drive
• Mandatory selection of SCSI adapter is required for Front Access Storage Cage (cable is included)
• Front Access Storage Cage based system is SCSI only. (IDE drives cannot be used.)

• Country-specific power cord

• Software media and documentation for first system on site

• Rackmount kit for rackmount systems (See Step 5 – M-Series Cabinet Enclosures)

• Minimum OS support: Tru64 UNIX V4.0F or OpenVMS V7.1-2

• DS10 Systems support one Storage Cage
• Selection of one Storage Cage is mandatory (no exceptions)

• DS10 Internal Storage Cage: DS10 System with Internal Cage supports three storage devices:
  - Either three internal hard disk drives or one 5.25-inch half height backup tape and two internal hard disk drives

• DS10 Front Access Storage Cage: DS10 System with Front Access Cage supports up to four storage devices:
  - Two Compaq Universal disk drives plus two internal disk drives, or
  – One Front Access Universal Tape Drive (AIT or DAT) and two internal disk drives

• Selection of one system disk drive is mandatory for the Internal Storage Cage (3X-BA10A-AA)
  - Mandatory selection of one IDE or one internal SCSI system disk drive
  - Mandatory selection of SCSI adapter and SCSI cable kit required for internal SCSI disks and tape

• DS10 Systems configured with the Internal Storage Cage include a 600-MB 40X half height CD-ROM and
  1.44-MB diskette in dedicated drive slots
• DS10 Systems configured with the Internal Storage Cage include three internal storage bays (two in the Storage cage
  plus one in the system box) that can be configured as follows:
  - Maximum of three internal disk drives (3.5-inch x 1-inch drives) or
  two internal disk drives (3.5-inch x 1-inch) and one 5.25-inch half height removable media device
• Mandatory selection of SCSI adapter and SCSI cable kit is required for internal SCSI disks or tapes
• IDE Disk drive cable kits are included with the system

NOTE: When a tape drive is ordered it will be installed in the top slot (Slot 3) and the CD will be installed in Slot 4.

DS-RZ3EF-WA

DS-RZ3FD-WA

• Selection of one Compaq Universal system disk drive or Universal tape drive is mandatory for each Front Access Storage Cage
• Mandatory selection of one Compaq Universal SCSI system disk drive or Universal tape drive
• Mandatory selection of SCSI adapter is required for Front Access Storage Cage
• SCSI cable with connections to the four disk drives is included with the Front Access Storage Cage

• DS10 Systems configured with Front Access Storage Cage include a 600-MB 24X slim line CD-ROM and 1.44-MB drive in dedicated drive slots
• DS10 Systems configured with the Front Access Storage Cage include four storage bays (two Compaq Universal SCSI disk drives and two internal SCSI drives) which can be configured as follows:
• Maximum of two internal disk drives (3.5-inch x 1-inch drives) and two Compaq Universal disk drives (3.5-inch x 1-inch) or one Front Access Universal tape drive (AIT or DAT) and two internal disk drives.
• Mandatory selection of SCSI adapter for Front Access Cage Systems
• SCSI cable included with Front Access Cage

NOTE: IDE drives may not be used on Front Access Cage systems.

(For Front Access Storage Cage)

• Front Access Storage Cage:
• Mandatory selection of SCSI adapter is required for Front Access Storage Cage
• Front Access Storage Cage includes SCSI cable kit for connection to four disks
• Internal Storage Cage:
• Mandatory selection of SCSI adapter and SCSI cable kit are required for Standard Storage Cage systems with SCSI disk or tapes

• Maximum 2-GB memory

• Systems include one memory kit; maximum two memory kits per system - each kit includes two industry-standard DIMMs with ECC support

3X-PBXRV-BA

• M-Series cabinet enclosures support up to 12 DS10 systems (H9A15).

• M-Series enclosures require selection of the following items:

• H9A10, or H9A15 Cabinet, 120V or 240V

• Cabinet front door based on cabinet height

• Factory integration

• A minimum of two AlphaServer DS10 systems is required in the H9A15 M-Series cabinet.

• Each system requires a DS10 M-Series Rackmount kit (3X-PBX01-AB).

• Each system requires a rack mount power cord.

• Up to six BA356 shelves supported; shelves cannot be mounted behind DS10 systems.

BA356/DS-SL13R Disk Shelves

• 12U of vertical cabinet space is reserved for one RA3000 controller shelf and up to five disk shelves mounted in top of cabinet, front to back; an additional 2U of vertical space is required for RA3000 controller shelf UPS.
• Disk shelves can be a combination of RA3000 DS-SWXRA-GN disk shelves and StorageWorks BA36R-RC/RD disk shelves.
• RA3000 controller shelf supports a maximum of four DS-SWXRA-GN disk shelves; third and fourth DS-SWXRA-GN disk shelf ordered will be installed in rear of M-Series cabinet; rear mounted shelves require that a 2-meter SCSI cable (BN37A-02) be ordered separately.
• Systems are supported in remaining vertical space. The following table considers space requirements for the DS10 system boxes and RA3000.
• For ballast requirements refer back to "Cabinet Configuration Chart for AlphaServer DS10 (3U) with StorageWorks Shelves (4U)"

• Rackmount kit must be ordered separately

• DS10 M-Series rackmount kit

3X-PBX01-AB

• Requires selection of one cabinet extender for each H9A10 or H9A15 cabinet

• Requires selection of door based on cabinet height

• Mandatory selection

YS-ASCAA-AA

• Add ballast kits as required

• Ballast is added to a cabinet at particular locations for specific configurations to meet safety regulations for installation, operation, and service; see Cabinet Configuration Charts

• Cabinets that contain systems and storage must be assembled by qualified assemblers: Compaq Manufacturing, CustomSystems, or an authorized Compaq Certified Integration Partner.
• For custom integration of systems, options, cabinet expansion offerings, and additional Compaq and third-party devices, or for other cabinets, doors, and trim kits of a different color, contact CustomSystems at 1-800-AT COMPAQ, or your local authorized Compaq Certified Integration Partner.

• Tape drives require an LVD adapter (3X-KZPCA-AA or 3X-KZPEA-DB) or single-ended UltraSCSI adapter (KZPBA-CA or KZPCM-DA) and country-specific power cord. NOTE: 3X-KZPEA-DB does not support SDLT tape/libraries.

• AIT hot-plug tape drives require two Universal slots

166505-291

• Storage controllers require a minimum operating system revision of Tru64 UNIX V4.0F or OpenVMS V7.1-2 unless noted otherwise.

• Each storage controller/adapter uses one PCI slot

(V5.1 or higher)

• Supported with BA610-6D, BA356 DS-SL13R-xx, or DS-SSL14-Rx shelves only.
• BA610-6D Nile Card must be at rev 0B to support internal RAID.
• When installed in BA356 shelves, part number DS-BA35X-FC is required for non-factory installations.
• Graphics card is required to run the DS-KZPCC-CE console utilities (SMOR) with SRM console versions lower than V6.0 or, alternatively can be run via serial line and terminal emulation software for SRM V6.0 or higher. PB2GA-JC/JD graphics cards are not supported.
• EV6 systems not supported.
• Tru64 UNIX V4.0F requires NHD3 and Patch Kit 4 (BL15) or later.
• Tru64 UNIX V5.1 requires Patch Kit 3 (BL17) and Early Release Patch C462.
  - Patch Kit 3 (BL17) is located at: T64V5117-C0046202-11060-Manual-
  ER-20010615.tar
  - Patch C462.02 is located at:
  http://ftp1.support.compaq.com/public/
  unix/v5.1/
  NOTE: This website is available in English only.
• TruCluster V5.1 (restricted to non-shared buses only)

(V4.0F/4.0G/
5.1/V5.1A)

• Supported with BA610-6D, BA356, and DS-SL13R-xx shelves only.
• BA610-6D Nile Card must be at rev 0B to support internal RAID.
• When installed in BA356 shelves, part number DS-BA35X-FC is required for non-factory installations.
• Graphics card is required to run the DS-KZPCC-AC console utilities (SMOR) with SRM console versions lower than V6.0 or, alternatively can be run via serial line and terminal emulation software for SRM V6.0 or higher. PB2GA-JC/JD graphics cards are not supported.
• EV6 systems not supported. Tru64 UNIX V4.0F requires NHD3 and Patch Kit 4 (BL15) or later.
• Tru64 UNIX V5.1 requires Patch Kit 3 (BL17) and Early Release Patch C462.
  - Patch Kit 3 (BL17) is located at: T64V5117-C0046202-11060-Manual-
  ER-20010615.tar
  - Patch C462.02 is located at: http://ftp1.support.compaq.com/public/
  unix/v5.1/
  NOTE: This website is available in English only.
• TruCluster V5.1 (restricted to non-shared buses only)

(V4.0F/
4.0G/
5.1/ V5.1A)

DS-KZPCC-AC

NOTE: Manufacturing may substitute BN37A-02 cable for specific cabinet configurations

DS-DSGGD-AC

DS-DSGGD-AD

• Requires selection of UltraSCSI adapter and SCSI cable

• StorageWorks Shelf supports seven 3.5-inch x 1.6-inch hard disk drives; with the addition of redundant power supply, six drives are supported

• StorageWorks shelf kits are mounted back-to-back in pedestals and cabinets

• Maximum six (10,000 rpm) or seven (7,200 rpm) drives supported in StorageWorks shelf

• One power supply supports a maximum of six 10,000 rpm disks

• Selection of RA3000 Solutions Software Kit is required

• Supported SCSI adapter - 3X-KZPBA-CC PCI 1-port UltraSCSI differential adapter

• Select one to four disk shelves

• Third and fourth DS-SWXRA-GN disk shelf ordered will be installed in rear of M-Series cabinet; rear mounted shelves require that a 2-meter BN37A-02 SCSI cable be ordered

DS-SWXRA-GN

• Note that second HSZ22 controller ordered is field installed only, not factory installed; requires BN37A-0E SCSI jumper cable be ordered separately

• StorageWorks Command Console (SWCC) software

• Platform specific software

• Installation scripts and installation documentation

• Enterprise Storage Array 10000 and RAID Array 7000 (HSZ70) product set are supported on AlphaServer DS10 systems

• Supported SCSI adapter for HSZ80/HSZ70 - 3X-KZPBA-CC PCI 1-port UltraSCSI differential adapter

• Supported SCSI adapter for HSG80 - KGPSA-BC PCI 1-port Fiber-Channel adapter

• Reference individual product information for operating system support.

• Systems include dual embedded 10/100 BaseT Ethernet ports (BN25G-xx cable must be ordered separately)

• Additional Ethernet ports can be added using available PCI slots

• OpenVMS V7.3 requires Tima Kit:
  - DEC-AXPVMS-VMS73_LAN-V0100—4.PCSI
• OpenVMS V7.2-2H1 requires OpenVMS Tima Kit located at:
  - http://ftp.support.compaq.com/patches/.new/
  openvms.shtml

NOTE: Two 10/100 Ethernet ports included with DS10 system.

3X-DE602-TA

Use BN34A or BN34B cables.

DEGPA-SA

3X-DEFPA-DC

BN34D-xx

BN34B-xx

Use BN25G, BN26M, BN24Q, or BN28Q twisted pair RJ45 cables.

3X-DEFPA-UC

Use BN25G, BN26M, BN24Q, or BN28Q twisted pair RJ45 cables.

3X-DEFPA-MC

• RAID Configuration Utility is accessible via console port for Tru64 UNIX and OpenVMS systems; optional graphics capability available

• Select graphics adapter, monitor, and country-specific keyboard if required
• Open3D license ships with PowerStorm 300/350 graphics accelerators.

• Graphics monitors other than those listed below can be used if compatible with SVGA graphics ordered with system

• A video cable, 6-foot/1.8-meter length, is included with all variants of monitors

• Video extension cable required if monitor is located more than 1.5-meter from system

• Monitors ship with, but are not integrated with the system

BN39C-02

• Keyboards are not included with the system and must be ordered separately

• Selection of country-specific keyboard is recommended

• Select an opal OpenVMS keyboard for use with VT5xx text terminals.

3R-A3480-AA

• Any terminal can be used as a console device

• Third-party console devices require an EIA-232 25-pin DSUB connector

• Requires Tru64 UNIX V5.0A or later and either TruCluster™ Server license
  (QL-6BRAC-AA) or TruCluster Plus Software Package (QP-6R9AC-AA)

• Requires OpenVMS V7.1-2 or later and OpenVMS Cluster license
  (QL-MUZAC-AA)

• Up to two PCI-to-System Area Network adapters (CCMAB-AA) are supported in a single system.

• Two-node clusters can be configured by ordering a CCMAB-AA for each node and one BN39B-04 or BN39B-10 cable; cable connects directly to CCMAB-AA in each node.
• For a two-node cluster that will not need to be rebooted when adding additional members, order one CCMAB-AA adapter and one BN39B-04 or BN39B-10 cable for each node, and one CCMHB-AA hub for the cluster.
• For three- or four- node clusters, order one CCMAB-AA adapter and one
  BN39B-04 or BN39B-10 cable for each node, and one CCMHB-AA hub for the cluster

• CCMHB-AA includes four CCMLB-AA line cards and supports up to four nodes; expansion up to eight system nodes can be achieved by adding up to four CCMLB-AA line cards.

• If two CCMAB-AAs are configured in each system, a second CCMHB-AA is required.

• If nodes must be separated by a distance longer than standard copper cables allow the CCMFB option converts the output of the standard CCMAB controller or CCMLB line card to single-mode fiber optic cable. The fiber optic connection may be up to 2,000 meters long between two CCMAB controllers connected in virtual hub mode, or 3,000 meters between a CCMAB controller and a CCMHB hub. (The connection from the CCMHB hub to a second system may also be 3,000 meters.) The CCMFB option requires a second PCI slot in the system from which it draws power only. It is normally connected to the corresponding CCMAB controller with the short BN39B-01 cable. The CCMFB is also used in the CCMHB hub where it occupies a slot normally used by the CCMLB line card, limiting expansion to four radial fiber optic connections.

• CCMHB-BA hub expansion box provides additional slots for up to eight fiber optic connections. Two standard length single-mode fiber optic cables are available (BN34R-10 and BN34R-31); however, users normally provide this fiber optic connection. Fiber optic connectivity is completely transparent to the systems using it and has no performance impact.

• For integration of MEMORY CHANNEL hubs into cabinet configurations, a rackmount kit (2T-MAVRK-AA) and power cord (BN35S-02) are required

3X-BA73P-AA

• Software processor code = E

• AlphaServer DS10Tru64 UNIX systems include Base license, Unlimited User license, Server Extension license, Internet Express, and Compaq Secure Web Server

• AlphaStation DS10 Tru64 UNIX systems include 2-user Base license

• AlphaServer DS10 OpenVMS systems include Base license with System Manager license and Compaq Enterprise Integration Server License Package for OpenVMS Revision V3.0A.

• AlphaStation DS10 OpenVMS systems include Base license, Concurrent Use
  1-user license, and NAS 150 Client license.

• Compaq Enterprise Integration Package includes licenses for TCP/IP Services for OpenVMS, DECwindows Motif for OpenVMS Alpha, DECprint Supervisor for OpenVMS Alpha Plus, DECprint Supervisor for OpenVMS Open, DECnet-Plus for OpenVMS Alpha End System, Archive/Backup System for OpenVMS Management Tools, Archive/Backup Agent for Windows NT, OpenVMS Disk Services for Windows NT, Office Server for OpenVMS, PATHWORKS 32, PATHWORKS V6 for OpenVMS – Advanced Server, and DIGITAL Office Server Client Access License

• OpenVMS Concurrent Use licenses provide the right to interactively use the operating system by the specified number of concurrent users on a designated OpenVMS system. OpenVMS Concurrent Use licenses can be moved from one system to another at user discretion and can be shared in a mixed OpenVMS VAX and OpenVMS Alpha cluster.

• OpenVMS Traditional Unlimited Use license is system specific and can only be used on one single system at a time. It cannot be shared between systems or in an OpenVMS VAX or OpenVMS Alpha Cluster.

QA-6M1AA-H8

• Select one of the optional CarePaq™ Priority Service Packages described below that best supports the customer’s operational requirements for system availability.

• CarePaq Priority Services are available for AlphaServer/AlphaStation systems running Tru64 UNIX or OpenVMS operating systems. Priority Services are designed for the growing number of customers who need support beyond the basic warranty. Five packages are offered - Priority, Priority 24, Priority Silver, Priority Gold, and Priority Executive with coverage for both Principal servers/stations and SSPs (Subsequent System Packages) - that meet a full range of customer support requirements.

• AlphaServer/AlphaStation DS10 systems include three years hardware warranty with 5x9, on-site Next Business Day response.
• New Compaq hardware options internal to the AlphaServer/AlphaStation enclosure receive the same warranty or service level as purchased with the server or station.
• External storage devices/cabinets carry their own level of warranty and should be quoted separately for uplifted warranty services (CarePaq Priority Service).
• In addition to the CarePaq Priority Services, uplifted warranty Supplemental Services are available for separate hardware and software support. For more information on Hardware and Software Supplemental Services and other service options available for AlphaServers and AlphaStations, consult your Sales Account Manager or visit http://www.compaq.com/services/
  NOTE: This website is available in English only.